Tennant 7400 Operator'S Manual Download Page 31

Page: 31 / 92

OPERATION

7400 (GM) 330970 (12--05)

4. Connect the supply hose to the FaST PAK

bag.

NOTE: If any dried concentrate is visible on the

supply hose connector or the on the FaST PAK

connector, soak and clean with warm water.

5. Place the FaST PAK carton in the carton

holder under the seat mounting plate on the

machine.

NOTE: Make sure the supply hose is not pinched.

6. Make sure to connect the supply hose onto

the hose storing plug when the supply hose

is not connected to the FaST PAK. This will

prevent the FaST solution system from

drying out and clogging up the hose.

7. When replacing an empty FaST PAK carton,

allow the new FaST PAK detergent to

gravity feed into the system for several

minutes prior to operating the FaST system.

If the detergent does not flow out of the

FaST PAK, simply squeeze and release the

hose several times. If the previous FaST

PAK was run dry, it may take up to 5--10

minutes of operation to remove any air

pockets in the system before you achieve

maximum foaming.

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands