Tennant 7400 Operator'S Manual Download Page 32

Page: 32 / 92

OPERATION

7400 (GM) 330970 (12--03)

CHANGING AN LPG FUEL TANK

1. Park the machine in a designated safe area.

2. Open the machine front cover.

3. Close the tank service valve on the LPG

tank.

4. Operate the engine until it stops from lack of

fuel, turn the ignition switch off, then set the

machine parking brake.

FOR SAFETY: When servicing machine,

Keep flames and sparks away from fuel

system service area. Keep area well

ventilated.

5. Put on gloves and remove the

quick-disconnect tank coupling.

6. Unlatch and remove the empty LPG fuel

tank from the machine and store the tank in

a designated, safe area.

NOTE: Make sure the LPG fuel tank matches the

fuel system (liquid tank with liquid system).

7. Carefully put the filled LPG tank in the

machine so that the tank centering pin

enters the aligning hole in the tank collar.

8. Fasten the tank hold-down clamp to lock the

tank in position.

07810

07811

07812

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands