Tennant 7400 Operator'S Manual Download Page 71

Page: 71 / 92

MAINTENANCE

7400 (GM) 330970 (3--05)

FaST SYSTEM

FaST SUPPLY HOSE CONNECTOR

The FaST supply hose connector is located on

the side of the the FaST PAK holder. Soak the

connector in warm water if detergent buildup is

visible. When a FaST PAK carton is not installed,

store the supply hose connector on the storing

plug to prevent the hose from clogging.

FaST SYSTEM FILTER SCREEN

The FaST system filter screen is located on top

the scrub head and filters the water from the

solution tank as it flows into the FaST system.

Remove the filter screen bowl and clean the filter

screen after every 50 hours of machine operation.

Empty the solution tank before removing the filter.

FaST SYSTEM AIR PUMP FILTER

The FaST system air pump filter is located on the

side of the air pump.

Remove and clean out the air filter with

compressed air after every 200 hours of FaST

scrubbing.

FOR SAFETY: When servicing machine,

wear eye protection when using

pressurized air or water.

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands