Tennant 7400 Operator'S Manual Download Page 56

Page: 56 / 92

MAINTENANCE

7400 (GM) 330970 (12--03)

LUBRICATION

ENGINE

Check the engine oil level daily. Change the

engine oil and oil filter every 100 hours of machine

operation. Use 10W30 SAE--SG/SH rated engine

oil.

Fill the engine with oil to the level indicated on the

oil dipstick.The engine oil capacity is 3.5 L (3.7 qt)

including the oil filter.

REAR WHEEL BEARINGS

Inspect the rear wheel bearings for seal damage,

and repack and adjust every 400 hours of

operation. Use Lubriplate EMB grease (Tennant

part number 01433--1).

FRONT WHEEL SUPPORT BEARING

The front wheel support pivots the front wheel.

The front wheel support bearings must be

lubricated every 200 hours of operation. Use

Lubriplate EMB grease (Tennant part no.

01433--1).

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands