Tennant 7400 Operator'S Manual Download Page 75

Page: 75 / 92

MAINTENANCE

7400 (GM) 330970 (12--03)

SQUEEGEE BLADES

REAR SQUEEGEE

Check the squeegee blades for damage and wear

daily. Rotate or replace either of the squeegee

blades if the leading edge is torn or worn half-way

through the thickness of the blade.

The rear squeegee has two squeegee blades.

Each blade has four wiping edges. To use them

all, start with one wiping edge. To use the next

wiping edge, rotate the blade end-for-end. To use

the next wiping edge, rotate the top edges down,

bottom edges up. To use the last edge, rotate the

blade end-for-end.

Replace any worn or damaged squeegee blades.

REPLACING OR ROTATING REAR SQUEEGEE
BLADES

1. Make sure the squeegee is raised off the

floor.

2. Shut the engine off and set the parking

brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Open the retaining band clamp and remove

the squeegee blade.

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands