Tennant 7400 Operator'S Manual Download Page 16

Page: 16 / 92

OPERATION

7400 (GM) 330970 (12--03)

RECOVERY TANK FULL LIGHT

The recovery tank full light starts blinking when

the recovery tank is full. The light will blink for one

minute and then stay on. Then the scrubbing

operations will shut off.

FUEL LEVEL LOW LIGHT

The fuel level low light comes on when the

gasoline or LPG fuel tank is almost empty. The

LPG fuel tank has five minutes of fuel remaining

when the level light comes on.

OK LIGHT

The OK light comes on after the control panel has

run through and passed a self-check every time

the machine is started. The OK light will go out

when the scrub or squeegee switch is activated,

or the engine speed is changed to (Fast).

HOURMETER

The hourmeter records the number of hours the

machine has been operated. The hourmeter

displays the number of hours in tenths of an hour.

Use this information to determine machine

maintenance intervals.

10886

10888

10889

07765

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands