Tennant 7400 Operator'S Manual Download Page 76

Page: 76 / 92

MAINTENANCE

7400 (GM) 330970 (12--03)

4. Replace or rotate the squeegee blade to

allow a new edge to face the front of the

machine.

5. Place the squeegee blade over the pins of

the squeegee frame.

6. Position the retaining band over the

squeegee blade. Latch the retaining band

clamp.

7. Adjust the squeegee blade leveling and

deflection as stated in

LEVELING THE

REAR SQUEEGEE

and

ADJUSTING REAR

SQUEEGEE BLADE DEFLECTION.

SIDE SQUEEGEES

The side squeegees control water spray and

channel water into the path of the rear squeegee.

Check the side squeegees for damage and wear

daily. Replace the side squeegee blades

whenever they become damaged or lose their

shape or resilience. Replace the squeegee

deflectors whenever they become worn.

REPLACING SIDE SQUEEGEE BLADES

1. Raise the scrub head.

2. Shut off the engine and set the machine

parking brake.

FOR SAFETY: Before leaving or

servicing machine; stop on level

surface, set parking brake, turn off

machine and remove key.

3. Remove the cotter pin, clevis pin, deflector,

and the retainer bracket from the front of the

side squeegee.

4. Pull the squeegee blade out the front of the

squeegee frame.

5. Slide the new squeegee blade onto the

frame.

NOTE: Lubricating the squeegee frame where

the squeegee makes contact will make it easier to

install the squeegee blade.

6. Replace the retainer bracket, deflector,

clevis pin, and cotter pin.

7. Repeat for the side squeegee on the other

side of the scrub head.

059420

Summary of Contents for 7400





























































































Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands

Tennant 7400, Operator'S Manual

Search results

Summary of Contents for 7400

Reviews:

Related manuals for 7400

Brands by name

Popular brands