Tennant 3640E Page 69 Service Manual Download

Page: 69 / 180

SWEEPING

3--19

3640E 330565 (5--00)

4. Remove the bolt and sleeve that holds the

clutch bar to the plastic side arm. This will

allow the pivot plate and handle assembly to

tip out for better access.

5. Remove the cotter pin and clevis pin from

the end of the main brush lift cable where it

attaches to the main brush lift lever.

6. Remove the nut from the clamp holding the

main brush cable to the mount plate.

7. Open the battery cover and remove the left

hand battery. Locate the end of the main

brush lift cable where it attaches to the

mount bracket below the vacuum fan.

Remove the cotter pin and clevis pin from

the lift cable and brush lift arm.

Summary of Contents for 3640E





















































































































































































Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands

Tennant 3640E, Service Manual

Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands