Tennant 3640E Service Manual Download

Page: 122 / 180

SWEEPING

3--72

3640E 330565 (5--00)

4. Pull the impeller straight up and off the shaft.

You may have to use a small pry bar or flat

screw driver to pry the impeller off. Do not

loose the key on the impeller shaft.

5. Position the new impeller on the impeller

shaft. Make sure the key is in place on the

shaft.

6. Hold the impeller from turning. Install the

hex nut on the impeller shaft. Tighten to

18 -- 24Nm (15 -- 20 ft lb).

7. Reinstall the vacuum fan housing on the

bearing backing plate. Hand tighten the

smaller hex screws.

8. Reinstall the vacuum fan assembly in the

machine. See TO INSTALL VACUUM FAN

ASSEMBLY instructions.

9. Start the machine and check the vacuum fan

for proper operation.

Summary of Contents for 3640E





















































































































































































Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands

Tennant 3640E, Service Manual

Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands