Tennant 3640E Page 63 Service Manual Download

Page: 63 / 180

SWEEPING

3--13

3640E 330565 (5--00)

4. Pivot the two filter lock bars back.

5. Remove the old filter by grasping the tabs

on both sides and pulling out. Pull the old

filter down and out of the filter compartment.

6. Position the new filter in the filter carrier.

Make sure the air flow arrows point in

toward the battery compartment.

7. Pivot the filter lock bars over the new filter

and reconnect the catch lock.

8. Rotate the filter cover back into place. Make

sure the upper portion of the vacuum wand

hose is in the proper location.

9. Reconnect the two filter clamps and snap

them into the lock position. Reinstall the

vacuum wand in the mount hole.

10. Start the machine and check the hopper

filter area for any air leaks.

Summary of Contents for 3640E





















































































































































































Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands

Tennant 3640E, Service Manual

Search results

Summary of Contents for 3640E

Reviews:

Related manuals for 3640E

Brands by name

Popular brands