Telex Communications Forum FOH User Manual Download Page 3 | Manualshive

Page: 3 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 3

Declaration of Conformity

The Manufacturer of the Products covered by this Declaration is

Klark Teknik Building, Walter Nash Road, Kidderminster, Worcestershire, DY11 7HJ.

The Directives Covered by this Declaration.

89/336/EEC Electromagnetic Compatibility Directive, amended by 92/31/EEC & 93/68/EEC

73/23/EEC Low Voltage Equipment Directive, amended by 93/68/EEC.

The Products Covered by this Declaration.

Equipment type

Product Name

Variants

Audio Mixing Console

Q2

Q2 VCA

Audio Mixing Console

Q2 Monitor

Meterbridge

Audio Mixing Console

QMR

Meterbridge

Audio Mixing Console

FMR

Audio Mixing Console

Forum

PA,Matrix,Mute

Audio Mixing Console

Forum Monitor

Meterbridge

Audio Mixing Console

XL200

Audio Mixing Console

XL250

The Basis on which Conformity is being Declared

The products identified above comply with the protection requirements of the EMC Directive and with the principal elements of
the safety objectives of the Low Voltage Directive, and the manufacturer has applied the following standardsQ

EN 55013 Q 1990

Limits and methods of measurement of radio disturbance characteristics of Broadcast Receivers and Associated Equipment.

EN 50082-1 Q 1992

Electromagnetic Compatibility - Generic Immunity Standard Part 1. Residential, commercial and light industry.

EN 60065 Q 1994

Safety requirements for mains operated electronic related apparatus for household and similar general use.

The technical documentation required to demonstrate that the products meet the requirements of the Low Voltage Directive has
been compiled by the signatory below and is available for inspection by the relevant enforcement authorities. The CE mark was
first applied in 1996.

SignedQ

................................

G.M.Squires

AuthorityQ

Product Support Manager.

DateQ

1st, January 1997.

Attention

The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations to use which must be
observed when these products are taken into service to maintain compliance with the above directive. Details of these special
measures and limitations to use are available on request, and are also contained in product manuals.

«
1
2
3
4
5
...
»

Summary of Contents for Forum FOH































































Reviews:

No comments

Related manuals for Forum FOH

Brand: Zelmer Pages: 42

Brand: VOX electronics Pages: 67

Brand: Numark Pages: 16

Equalizer LEF-317

Brand: FAME Pages: 15

Brand: Zoom Pages: 45

Brand: Marantz Pages: 28

Brand: Maestro Pages: 8

Brand: Laney Pages: 19

Brand: Russell Hobbs Pages: 54

Brand: Philips Pages: 2

Brand: Fulltone Pages: 2

Maxi Mix Plus M63210-33

Brand: Barnstead International Pages: 16

Brand: Art Pages: 1

Brand: Rane Pages: 4

Brand: Fostex Pages: 14

Brand: Fostex Pages: 27

Brand: Fostex Pages: 32

Brand: MUHLER Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands