Telex Communications Forum FOH User Manual Download Page 61

Page: 61 / 62

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 61

GENERAL SERVICING

Servicing should be referred to factory personnel, or your
authorized DDA distributor.

If you require to remove a module then follow the steps below.

Remove the upper and lower identification strips by pulling
carefully up at one end, then along, unclipping each section very
carefully.

Remove three screws which hold the module in place located at the
bottom, top, and rear, near the bottom of the connector panel.

To remove the module, lift the bottom of the panel, then pull the
module back about 2cms. so that the top is disengaged from the
frame.

Unplug the ribbon cable from the module along with any earth
wires that may be attached.

Replacement is a reversal of the above.

Summary of Contents for Forum FOH































































Search results

Summary of Contents for Forum FOH

Reviews:

Related manuals for Forum FOH

Brands by name

Popular brands

Telex Communications Forum FOH, User Manual

Search results

Summary of Contents for Forum FOH

Reviews:

Related manuals for Forum FOH

Brands by name

Popular brands