Telex Communications Forum FOH User Manual Download Page 5 | Manualshive

Page: 5 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 5

SAFETY

PRECAUTIONS

IMPORTANT - PLEASE READ BEFORE

INSTALLING YOUR FORUM CONSOLE

Strong sources of electromagnetic radiation e.g. high power
cabling, video monitors and radio transmitters may cause
degradation of of the audio quality due to induced voltages in the
chassis and connection leads. Site the console away from such
sources. For the same reason it is advisable to site the power supply
away from the console.

!

Electronic components are susceptible to conditions of
excessive heat or extreme cold so take care not to use
your console under such conditions.

!

Before powering up the console make sure that the
power supply voltage selection matches the local mains
supply.

!

Never connect or disconnect the power cable with out
switching off the power supply. Similarly switch of the
console before removing or servicing modules.

!

Do not attempt to wipe clean the console with a
cleaning liquid. Most surfaces can be simply cleaned
with a soft dry brush. Should the chassis or channel
ident strips need cleaning use only water or an alcohol.
Solvent based products should not be used as they will
damage these parts.

If you spill any liquids in the console e.g. coffee on the faders
switch off the power supply immediately. Consult you authorised
dealer before attempting any cleaning.

«
...
3
4
5
6
7
...
»

Summary of Contents for Forum FOH































































Reviews:

No comments

Related manuals for Forum FOH

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 2

M7CL StageMix V1.5

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 2

Brand: Reloop Pages: 2

Brand: Kambrook Pages: 24

Brand: Rachel Allen Pages: 16

Profi Cook UM 290

Brand: Clatronic Pages: 54

Brand: Omcan Pages: 28

Vantage Pro2 6312 Console

Brand: DAVIS Pages: 56

Brand: Amek Pages: 104

Brand: Samson Pages: 8

Brand: Singer Pages: 16

Brand: T-Rex Pages: 5

Brand: Stageline Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands