Telex Communications Forum FOH User Manual Download Page 29 | Manualshive

Page: 29 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 29

ON
The ON switch enables the channel signal path, and is indicated by
an LED in the switch when the channel is active. When OFF, all
post-fade auxiliary sends and routing assignments are muted.

PFL
The PFL button Por SOLO) feeds the post-EQ, pre-fader signal to
the monitor section Ploudspeakers or headphones), replacing the
master signal. The main stereo output is not affected. The red LED
in the PFL switch illuminates when the PFL function is active.PFL
signals from different sources that are active simultaneously are
summed.

SIGNAL METER PLED)
A five segment LED signal meter shows when a signal is present
above a threshold of -13dBu, and will show peak signals of up to
+17dBu. If the top led is on partly or continuously, the signal is
close to clipping. The meter shows the higher of the left or right
channel signals.

STEREO FADER
The fader is the main signal level control for the channel, and is a
long-throw type which gives smooth control of the channel level.

«
...
27
28
29
30
31
...
»

Summary of Contents for Forum FOH































































Reviews:

No comments

Related manuals for Forum FOH

Brand: Plush Pages: 7

Brand: Aion Electronics Pages: 10

REVIVALDRIVE HOT ROD EDITION

Brand: Origin Effects Pages: 20

Brand: Baldus Pages: 28

BMHD0250 Signature Collection

Brand: Wolfgang Puck Pages: 8

Brand: Omnitronic Pages: 20

Brand: DAPAudio Pages: 16

Brand: Nady Audio Pages: 2

Brand: Makita Pages: 16

iMultiMix 16 USB

Brand: Alesis Pages: 44

Brand: Sound Devices Pages: 210

Brand: Philips Pages: 2

Brand: Rane Pages: 8

Brand: Rane Pages: 12

Brand: KYOWA Pages: 3

Brand: Arzum Pages: 28

Brand: JBL Pages: 28

Brand: Hotpoint Ariston Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands