Telex Communications Forum FOH User Manual Download | Manualshive

Page: 31 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 31

THE STEREO MUTE INPUT MODULE

This module is identical to the standard stereo input module other
than for the addition of the 8 mute group switches. These switches
assign the channel to one or more mute groups and will cause the
channel to CUT if the master cut for the assigned mute group is
operated. The mute groups do not have to be the same as the audio
groups and great flexibility can be achieved by having different
assignments. A SAFE switch is provided to prevent a channel from
responding to a master cut while retaining the assignment.

«
...
29
30
31
32
33
...
»

Summary of Contents for Forum FOH































































Reviews:

No comments

Related manuals for Forum FOH

Powerhead PA Mixer

Brand: KAM Pages: 4

Brand: Gizmo Pages: 8

Brand: Stone Pages: 20

Brand: VOX electronics Pages: 76

Brand: madbeanpedals Pages: 17

Brand: MMM Pages: 30

CHM-7PK - PowerSelect Hand Mixer

Brand: Cuisinart Pages: 24

MP-201 Multi-Pedal

Brand: Moog Pages: 12

Brand: EarthQuaker Devices Pages: 23

Brand: Sony Pages: 3

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 14

CMT-HPZ9 - Micro Hi Fi Component System

Brand: Sony Pages: 20

Brand: Sony Pages: 26

Brand: Sony Pages: 86

Brand: Sony Pages: 364

Brand: Sony Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands