Telex Communications Forum FOH User Manual Download Page 41 | Manualshive

Page: 41 / 62

background image

FORUM OPERATION AND MAINTENANCE MANUAL 9601

PAGE 41

10 WAY SELECTOR MODULE

This module provides additional inputs for the 2 TRK position of
the monitor selection switch on the master module. An EDAC
connector is used to provide the 10 stereo input connections while 2
male XLR connectors provide outputs which can then be connected
by external cables to the 2 track input of the master module.

The module could also be used as a 10 way source selector for the
stereo input module for example.

Each button is associated with an identification strip to allow for
source labelling.

An alternative version of this module, fitted with female XLR
connectors may be used to expand the Monitor Output of the
console for use with other monitoring systems.

«
...
39
40
41
42
43
...
»

Summary of Contents for Forum FOH































































Reviews:

No comments

Related manuals for Forum FOH

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 32

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 2

Brand: Yellowtec Pages: 23

Brand: Yamaha Pages: 21

Brand: Numark Pages: 20

Brand: TL Audio Pages: 21

Brand: VADO Pages: 4

Brand: Strymon Pages: 8

Brand: Harman Pages: 56

Brand: Behringer Pages: 19

Brand: SpinCore Technologies Pages: 30

Brand: Russell Hobbs Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands