manualshive.com logo in svg

Telegesis ETRX2USB, Command Manual, Page: 30 / 101

Share
Download
Telegesis ETRX2USB Command Manual Download Page 30

 

 

R305 AT Commands

 

 

©2011 Telegesis (UK) Ltd 

- 30 - 

 AT Command Manual (Rev 3.05) 

+POLL 

– Poll The Parent Device 

Execute Command 

AT+POLL 

 
Poll the parent device for new data. 
 
Note:  Action  0010/8010  is  recommended for 
periodic polling using the built-in timers. 
 

Use on 

SED, MED 
 

Response 

OK  
 

or 

 
 ERROR<errorcode> 

 
 
<errorcode> represents the error code explained in 
section 3.   
 

SW release  

R300   

 

 

 

 

       

● 

 

+REJOIN 

– Rejoin the network 

Execute Command 

AT+REJOIN:b 

 
If b is set to 0 join without the known network 
key (unencrypted) and if  b is set to 1 join 
encrypted. 
 

Use on 

SED,MED 
 
 

Notes 

Polling a parent on an end device that has 
lost its parent will automatically call 
AT+REJOIN:1.  Furthermore functionality 
0012 and 0013 make use of this command. 
 

Response 

OK  
 

or 

 
ERROR<errorcode> 

 
 
If  the  contact  with  the  network  has  been  lost 
because  an  end  device  has  lost  its  parent,  the 
network  has  changed  channel,  or  updated  its 
encryption  key  the  command  AT+REJOIN  can  be 
used to rejoin the network.  
 
<errorcode> represents the error code explained in 
section 3.   

SW release  

R300   

 

 

 

 

       

● 

 

Summary of Contents for ETRX2USB






































































































Reviews:

No comments