manualshive.com logo in svg

Tektronix VM700T, User Manual

Share
Download
Tektronix VM700T User Manual Download Page 60

Configuring the VM700T Video Measurement Set

VM700T Option 01 (NTSC) & Option 11 (PAL) User Manual

2- 23

3.

Scroll the control knob to display the desired value or select Make it
undefined if you wish to remove the limit.

4.

Select the

Accept Input

soft key or touch the screen anywhere inside the

directory window to return the control knob to its scrolling function.

Setting a pair of limits “backwards” (setting an upper limit lower than its lower
limit) always generates an alarm flag on the Auto mode display.

Alarm limits may be set inside Caution limits, but then only Alarm limit
violations are flagged.

The measurement set has two RS-232-C serial ports and a parallel printer port.
Either serial port can be attached to an ASCII, Epson, HP LaserJet, or PostScript
printer, or to a modem or terminal for serial communication during remote
operation. The parallel printer port may be used for any printer having a
Centronics-compatible parallel printer interface. The Communication Setup file
tells the measurement set how the RS-232-C ports are configured. The factory
default settings are the proper settings for a serial Epson LQ-570 printer
connected to Serial Port 1.

NOTE

. Option 48, the GPIB Interface option, adds a parallel GPIB port. Any or

all of the logical ports may be set to GPIB when the option is installed.

Port and Format Assignments.

The standard VM700T Video Measurement Set

has the following three physical ports:

H

Serial Port 0

H

Serial Port 1

H

Parallel Printer Port

NOTE

. The GPIB Interface, Option 48, adds GPIB to the available port list for

Copy, Log, Report, and Remote.

It has the following five logical ports:

H

Copy

: the port to which screen dumps generated by pressing the Copy

button, as well as printouts generated by the Configure mode Print File soft
key, are sent. The physical port may be either of the serial ports or the
parallel printer port.

H

Report

: the port to which Timed Event reports are sent. Again, the physical

port may be either of the serial ports or the parallel printer port.

Communication Setup

(File)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for VM700T











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands