Tektronix PFG 5105, Instruction Manual

Page: 6 / 89

(
(
LIST OF ILLUSTRATIONS
Fig. 1-1. Trigger to timing and phase
relationships .............................................. 1-2
Fig. 1-2A. Typical FM Response:
121 kHz to 1.2 MHz . .............................. 1-3
Fig. 1-2B. Typical FM Response:
1.2 MHz to 12 MHz .. .............................. 1-4
Fig. 1-3. Typical Amplitude Flatness for
Sine Wave ................................................. 1-7
Fig. 1-4. Typical Amplitude Flatness for
Square Wave ............................................. 1-8
Fig. 1-5. Typical Amplitude Flatness for
Triangle Wave ........................................... 1-9
Fig. 1-6. Typical Amplitude Flatness for
Pulse ........................................................ 1-11
Fig. 2-1. Power cords ............................................. 2-1
Fig. 2-2. Line voltage selection/fuse
replacement. ............................................. 2-2
Fig. 2-3. Rear panel GPIB connector .................... 2-3
Fig. 2-4. Front panel numeric setting change . .... 2-4
Fig. 2-5. Controls and connectors . ....................... 2-6
Fig. 2-6. Triangle generator architecture ............. 2-15
Fig. 2-7. AM Distortion ........................................... 2-15
Fig. 2-8. Relationship Between Width, Delay
and Period . ............................................. 2-16
Fig. 3-1. Command associations to controls ....... 3-6
Fig. 3-2. Pulse and Width Relationships . ........... 3-24
Fig. 3-3.
ASCII
and IEEE (GPIB} Code Chart ... 3-26
Fig. 3-4. Definition of STB bits . ........................... 3-30
LIST OF TABLES
Table 1-1
Table 1-2
Table 1-3
Table 1-4
Table 1-5
Table 1-6
Table 1-7
INTERFACE FUNCTION SUBSETS
...... 1-1
WAVEFORMS, OPERATING MODES,
AND PARAMETERS ................................ 1-2
FREQUENCY CHARACTERISTICS
(STANDARD ANALOG FUNCTIONS) .... 1-5
GENERAL OUTPUT
CHARACTERISTICS ................................ 1-6
OUTPUT CHARACTERISTICS ............... 1-7
INTERNAL T RlGGER ............................ 1-12
EXTERNAL TRIGGER ........................... 1-12
Table 1-8 SYNTHESIZER (OPTION 02} .............. 1-13
Table 1-9 FREQUENCY SWEEP .......................... 1-13
Table 1-10 INPUTS AND OUTPUTS ...................... 1-14
Table 1-11 GPIB CHARACTERISTICS ................... 1-15
Table 1-12 MISCELLANEOUS ELECTRICAL
CHARACTERISTICS .............................. 1-15
Table 1-13 SOURCE POWER REQUIREMENTS
(PFG 5505 only) ................................... 1-15
PFG 5105/5505 Instruction Manual
Table 1-14 ENVIRONMENTAL ................................. 1-16
Table 1-15 MECHANICAL. ....................................... 1-17
Table 2-1 POWER-ON DEFAULT SETTINGS ........ 2-5
Table 2-2 FRONT PANEL ERROR CODES ......... 2-10
Table 2-3 SPECIAL FUNCTIONS ......................... 2-11
Table 2-4 DEMO SETUPS .................................... 2-12
Table 2-5 GENERATING SINE, TRIANGLE,
SQUARE AND DC FUNCTIONS ......... 2-13
Table 2-6 GENERATING PULSE FUNCTIONS ... 2-13
Table 2-7 MINIMUM RECOVERY TIME ............... 2-17
Table 2-8 VALID START/STOP RANGES ............. 2-18
Table 2-9 USING THE SWEEP GENERATOR .... 2-18
Table 3-1 ERROR QUERY AND STATUS
INFORMATION (Bus Reportable) ....... 3-31
Table 3-2 FRONT PANEL ERROR CODES
(Non-Bus Reportable} .......................... 3-35
Table 3-3 POWER-ON DEFAULT SET TINGS ...... 3-36
iii