Teka 111000056, User Manual

Page: 37 / 264

35
Installation & Maintenance
English
Installation
This information is exclusively for the installer
who is responsible for assembly and electrical
connection. The manufacturer will not accept
liability for possible damage caused if you install
the oven yourself.
",Ê -//"
UÊ /œÊ >˜`iÊ Ì iÊ œÛi˜]Ê ÕÃiÊ Ì iÊ }Àˆ«ÃÊ >ÌÊ Ì iÊ
sides. Do not use the door handle to lift the
oven.
UÊ 7 i˜Ê ˆ˜ÃÌ>ˆ˜}Ê Ì iÊ œÛi˜Ê ՘`iÀÊ >Ê VœÕ˜ÌiÀ]Ê
follow the instructions for installing it.
UÊ ˜Ê}i˜iÀ>]Ê«ÀœÌÀÕ`ˆ˜}Êii“i˜ÌÃÊ­vÕÀ˜ˆÌÕÀiÊÀi
-
inforcements, pipes, socket bases, etc.) at
the back of the unit must be avoided.
UÊ 7 i˜ÊÌ iÊL>ÃiʜvÊÌ iʓ>ˆ˜Ê«œÜiÀÊÜVŽiÌʈÃÊ
inside the unit in which the oven is installed,
this must be done in the shaded area.
Figure 2.
UÊ / iÊ Õ˜ˆÌÊ ˆ˜Ê Ü ˆV Ê Ì iÊ œÛi˜Ê ˆÃÊ ˆ˜ÃÌ>i`Ê >˜`Ê
adjacent units must withstand temperatures
higher than 85 ºC.
UÊ / iÊ ˆ˜ÃÌ>>̈œ˜Ê ˆ˜ÃÌÀÕV̈œ˜ÃÊ “ÕÃÌÊ LiÊ >`
-
hered to strictly. If not, the oven’s ventilation
circuit may become blocked, causing high
temperatures that could damage the kitchen
unit and the appliance itself.
UÊ œÀÊ Ì ˆÃÊ «ÕÀ«œÃi]Ê V iVŽÊ Ì iÊ Õ˜ˆÌÊ “i>ÃÕÀi -
ments and those of the holes to be drilled in
Ì iÊ՘ˆÌÃ]Ê>ÃÊà œÜ˜Êˆ˜ÊÌ iÊvœœÜˆ˜}Êw}ÕÀiÃ\
Column installation.
ÈäÊV“ÊœÛi˜\ʈ}ÕÀiÊÇI°
{xÊV“ÊœÛi˜\ʈ}ÕÀiÊnI°
CAUTION
IÊ7 i˜Êˆ˜ÃÌ>ˆ˜}Ê «ÞÀœÞ̈VʜÛi˜Ã]Ê"Ê "/
drill any holes in the unit inside the shaded
areas.
Undercounter installation.
ÈäÊV“ÊœÛi˜\ʈ}ÕÀiʙI°
{xÊV“ÊœÛi˜\ʈ}ÕÀiÊ£äI°
Ê 7,
IÊ7 i˜Êˆ˜ÃÌ>ˆ˜}Ê «ÞÀœÞ̈VʜÛi˜Ã]Ê"Ê "/
drill any holes in the unit inside the shaded
areas.
ELECTRICAL CONNECTION
/ iÊwÌÌiÀʓÕÃÌÊi˜ÃÕÀiÊÌ >Ì\
UÊ / iÊ “>ˆ˜ÃÊ «œÜiÀÊ ÛœÌ>}iÊ >˜`Ê vÀiµÕi˜VÞÊ
correspond to what is marked on the identi-
wV>̈œ˜Ê«>Ìi°
UÊ / iÊ `œ“iÃ̈VÊ ÜˆÀˆ˜}Ê ÃÞÃÌi“Ê V>˜Ê ÜˆÌ ÃÌ>˜`Ê
Ì iʓ>݈“Õ“Ê«œÜiÀʓ>ÀŽi`ʜ˜ÊÌ iʈ`i˜Ìˆw -
cation plate.
UÊ vÌiÀÊ Vœ˜˜iV̈˜}Ê Ì iÊ «œÜiÀÊ ÃÕ««Þ]Ê V iVŽÊ
that all electrical parts of the oven are work-
ing correctly.
OVEN INSTALLATION
For all ovens. After the electrical connection has
Lii˜Ê`œ˜i\
1. Position the oven inside the unit and ensure
that the feed cable is not trapped or in con-
tact with parts of the oven that heat up.
2. Make sure that the body of the oven is not
in contact with the walls of the unit and that
there is a minimum space of 2 mm between
adjacent units.
3. Centre the oven in the unit so that there is a
minimum space of 5mm between the oven
and the doors of the furniture that surrounds
it. Figure 3.
4. Open the door and insert the plastic plugs
supplied with the oven into their respective
housings. Figure 11.
5. Fasten the oven to the unit with the screws
supplied, screwing them into the unit through
the stops.