![Tecnoalarm TP8-64 User Manual Download Page 20](http://html1.mh-extra.com/html/tecnoalarm/tp8-64/tp8-64_user-manual_1071819020.webp)
Signaling
User Manual -
TP8-64
2-6
2.2
LED SIGNALING OF THE TP SDN ELECTRONIC KEYPAD
The electronic keypad provides coloured LED for signaling of the alarms and system status.
2.2.1
PROGRAM ALARM LED - YELLOW
The program alarm is detected only if the control panel is armed.
The yellow program alarm LED signal program alarms as follows:
z
LED blinking
= a program alarm is active.
The LED starts blinking as soon as one of the zones of the
program is opened or in alarm and remains blinking for the
entire alarm time. On expiry of the alarm time, the alarm is
stopped and the LED becomes lit.
z
LED on
= a program alarm has been stopped and stored in the event
buffer (alarm memory).
The LED remains lit until the control panel is armed again.
z
LED off
= no alarm has occurred.
The program alarm is logged in the event buffer of the control panel.
According to programming, the indoor and/or outdoor sirens as well as the logic output
PGM are activated for program alarm.
2.2.2
GENERAL ALARM LED - RED
The general alarm is a direct alarm that is always enabled.
Among the general alarms count:
z
Antimasking alarm
The radio receiver has been jammed.
z
Supervision alarm
One of the radio devices has not transmitted any test signal/alarm for a period
superior to the supervision interval programmed.
z
False key
An unknown key has been inserted in one of the keypoint connected.
z
False code
32 or more keys have been pressed on one of the consoles and keypads connected
without entering a valid code.
z
GSM fault
The mobile phone does not answer to the interrogations by the GSM interface
TECNOCELL for a period of approximately 10s.
z
Cut telephone line
The telephone line voltage is missing for a period of approximately 1 minute.
z
Low battery
The battery voltage has fallen to a value below the minimum guaranteeing correct
functioning of the control panel (<11V) or voltage of the battery of one of the radio
devices connected is insufficient (<2.7V).
z
Power failure (230V AC)
L E D o ff
L E D b lin k in g q u ic k ly
L E D b lin k in g s lo w ly
L E D o n
P ro g ra m in s t a n d -b y
P ro g ra m in p re -a rm in g p h a s e a c t ive
P ro g ra m p a rt s e t
P ro g ra m a rm e d
L E D o ff
L E D b lin k in g q u ic k ly
1 fla s h
L E D o n
K e y p a d in s t a n d -b y
A n o t h e r k e y p a d in u s e
K e y s t ro k e
K e y p a d a c t ive (va lid c o d e )
L E D o ff
L E D b lin k in g
L E D o n
N o a la rm
A la rm a c t ive
A la rm s t o re d (a la rm m e m o ry )
L E D o ff
L E D b lin k in g q u ic k ly
L E D b lin k in g s lo w ly
L E D o n
N o a la rm
D ire c t o p e n z o n e s o n a rm in g
A la rm a c t ive
A la rm s t o re d (a la rm m e m o ry )
5
K EYP A D
4
G EN ER A L C O N T R O L L ED (O C G )
G EN ER A L A L A R M L ED
3
C O M M A N D M O D E L ED
S T A T U S P R O G R A M L ED (1 . . . 4 )
1
2
Summary of Contents for TP8-64
