manualshive.com logo in svg

TechnipFMC Smith Meter MPU 1600c, Installation, Operation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter MPU 1600c Installation, Operation & Maintenance Manual Download Page 93

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 93

5.  Verify software seal.

 

 

 

•  Select Information

 

 

•  Verify that the Parameter Seal shows a closed lock

 

 

•  Select the back button in the upper left hand corner of the display

 

•  Select Maintenance

 

 

•  Select reset passwords

 

 

 

•  Press green accept button

 

 

•  Verify  that  an  error  message  is  displayed,  “Failed  to  reset  passwords 

 

 

 

 

because no flash drive found.”  Touch the display anywhere to acknowledge 

 

   the 

message.

 

 

•  Select the back button in the upper left hand corner of the display

6.  Finding the meter serial number

 

•  Select Configuration

 

 

•  Select Security Level 4

 

 

•  Enter 4-digit pin [default is 4444]

 

 

•  Press Login

   • Press 

Connections

 

 

 

•  Notice that all options are greyed out and that a lock appears in front 

 

 

 

 

 

of all of the selections.

 

 

 

•  The Device Serial Number is shown under the selection and can be 

 

 

 

 

 

read from this screen. Write down the number for later reference.

 

 

 

•  Press the return key (upper left hand corner)

MPU Series C I/O/M Manual 

 

 

 

 

 

 

Integrated Touch Screen Display

Summary of Contents for Smith Meter MPU 1600c

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands