manualshive.com logo in svg

TechnipFMC Smith Meter MPU 1600c, Installation, Operation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter MPU 1600c Installation, Operation & Maintenance Manual Download Page 72

Page 72 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

MPU Series C I/O/M Manual 

 

 

 

 

 

 

 

Web User Interface

 

6.7.2.1.2.  Example RTD Calibration

Apply test inputs to meter

 

 

The calibration can now be tested. Apply an actual signal to the meter press “Test” to 

check if the meter reads the correct value. Enter “Submit” to enter new factors if the 

calibration was successful.

 

6.7.2.2.   Simulate Flow

 

(Path:  Diagnostics > Commissioning  > Simulate Flow)

 

This option allows the meter to run in a simulated ("forced") state. While in this state, 

the values displayed 

are not

 real measured information. To simulate:

(1)  Enter a desired flow velocity; typical 700-1700
(2)  Enter a desired velocity of sound (VOS); typical 0-20
(3)  Select a desired flow profile from the drop down menu (0-8)
(4)  Press   button to start simulation

A "Forced Values" indicator will appear (if not already present) in the bottom right corner 

of the display denoting simulation started.

Profile

Behavior

0

Standard ("Normal") operation

1 - 8

Various non-standard flow

profile types

 

Summary of Contents for Smith Meter MPU 1600c

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands