manualshive.com logo in svg

TechnipFMC Smith Meter MPU 1600c, Installation, Operation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter MPU 1600c Installation, Operation & Maintenance Manual Download Page 45

Issue/Rev. 0.1 (11/18) ║ MNKS025 • Page 45

 

6.4.2.2.  Network Settings

 

(Path:  Settings > Network Settings)

 

Configure the necessary Ethernet settings for network communication.
•   DHCP – Meter will automatically be assigned an IP per the network's DNCP 

 

 server.

•   Fixed – allows for manual configuration of the meter's network settings.
•  Saved button – accepts new configuration.

  

NOTE:

 These changes will not take effect until the meter has been power cycled.

 

  

 

6.4.2.3.  Flow Calibration

 

(Path:  Settings > Flow Calibration)

 

The menu allows for implementation of a meter factor that is variable with the flow rate 

over up to 16 meter factor nodes. Each node is comprised of 2 parameters: a flow rate 

and a corresponding meter factor. 

Calibration node 1 sets the meter factor for all flow rates at or below the entered flow 

rate. Additional calibration nodes can be entered in order from low to high flow rate in 

order to vary the meter factor with flow rate. 
Not all 16 available calibration nodes need to be configured. The last configured cali-

bration node sets the meter factor for all flow rates at or above the entered flow rate. If 

a single calibration node is configured then this sets the meter factor for all flow rates 

above and below the flow rate set point.  

Calibration Node Entry Guidelines:

 

1)  All 16 of the calibration nodes do not need to be configured. Start the calibration 

 

 

 

range at Node 1 and leave unused nodes set to (0,0). 

 

2)  Use the single calibration Node 1 to set a fixed meter factor valid for all flow 

 

  rates.

 

3)  Program additional nodes starting at the lowest flow rate at Node 1 progressing 

 

 

 

to the highest.

 

4)  Program nodes contiguously (don’t leave unused nodes in the middle of the 

 

  list).

 

5)  The first configured node in the list sets the meter factor for all flow rates at or 

 

 

 

below the entered flow rate

MPU Series C I/O/M Manual 

 

 

 

 

 

 

 

Web User Interface

Summary of Contents for Smith Meter MPU 1600c

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands