manualshive.com logo in svg

TechnipFMC Smith Meter MPU 1600c, Installation, Operation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter MPU 1600c Installation, Operation & Maintenance Manual Download Page 18

Page 18 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

MPU Series C I/O/M Manual 

 

 

 

 

 

 

Operation of MPU

 

3.5. 

Mechanical Installation

Installation of the MPU flowmeter should follow good piping practices, such as alignment 

of the pipe center lines before installing the meter in order to minimize compressive, 

tensile or torsional stresses placed on the meter. A temporary, straight pipe spool can 

be used to align the process piping prior to meter installation if required. Do not use the 

meter to align the piping.

It is important that no portion of the gasket intrude into the ID of the pipe. This could 

cause a distorted flow profile in the meter that will affect the performance and stability of 

the measurement.

Gasket, bolt and nut materials selected must be compatible with the application environ-

ment and specifications. Pipe supports should be installed upstream and downstream 

of the meter to provide sufficient support of the process piping, in accordance with good 

piping practices.

It is recommended that the meter be installed in the section of piping where the pressure 

is highest, downstream from pumps and upstream from flow control valves. When it is 

expected that flow will be intermittent, the meter should not be mounted at or near a low 

point or high point in the piping. Solids or water will settle in a low point in the piping; gas 

will accumulate in a high point in the piping. Both of these conditions may impede proper 

meter operation.

The installation instructions described herein are intended to be general recommendations 

and, therefore, may require modification to fit your specific application.

 

 Warning: 

Care must be taken in the installation of the meter. The installer must comply 

 

 

 

with all national, regional, and local codes.

 

3.6. 

Handling of Flowmeter

Do not lift the flowmeter by the electronics box. Use the lifting lugs that are attached to 

the flanges. Reference Bulletin 

MNKS020

.

 

3.7. 

Flow Conditioning

 3.7.1. 

MPU 800 Recommended Installation

 

The recommended installation for the MPU 800c is 10D upstream straight run. For optimum 

performance it is recommended to keep partial restrictions or variable flow diversions such 

as control valves away from the upstream area. Consult factory for an evaluation in the 

case of a complex upstream piping geometry. When using flow conditioning the meter 

should be installed a minimum of 5D from the flow conditioner outlet.
The meter run must be the same pipe diameter as the meter inlet and concentrically cen-

tered so that neither the pipe edge nor gasket protrude into the flow stream. For correct 

centering it is recommended to use the centering dowel pin provided on the meter flange.

Summary of Contents for Smith Meter MPU 1600c

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands