manualshive.com logo in svg

TechnipFMC Smith Meter MPU 1600c, Installation, Operation & Maintenance Manual

Share
Download
TechnipFMC Smith Meter MPU 1600c Installation, Operation & Maintenance Manual Download Page 84

Page 84 • MNKS025 ║ Issue/Rev. 0.1 (11/18)

 

7.3.1.2.  Display Configuration - General

Date/Time

 – Adjust the date and time of the display unit. Once the display has been 

sealed the date and time adjustment will be locked out.

Set Passwords

  –  Update  the  passwords  for  either  level  4  or  level  5  access.  The 

screen will prompt for the old password and for the new password to be entered twice 

for confirmation.

The password is unique to the display and is not shared with the ultrasonic meter.  

IMPORTANT:

 Record all password modifications and store in a secure location.

 
 

7.3.1.3.  Display Network Settings

The network settings are to configure the address of the Display on the network. Note 

that this is not the address of the meter that the display is connecting to. The display is 

required to have a unique IP address because it exists as a device on the IP network.  

There are two modes to create the display’s network address:

DHCP

 – The Dynamic Host Configuration Protocol is used to request the IP address 

from the network server. With this configuration checked, the DHCP server assigns a 

local IP address to the Display connected to the local network. This is the default net-

work setting from the factory.

Fixed

 – If the Ethernet network does not support DHCP or if the meter is not connected 

to a network a fixed IP address should be used. The network settings for the fixed ad-

dress must be entered manually on the display screen.  

 

Note:

 The unit must be power cycled for the new settings to take effect.

MPU Series C I/O/M Manual 

 

 

 

 

 

 

Integrated Touch Screen Display

Summary of Contents for Smith Meter MPU 1600c

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands