background image

 

11

10.

 

LIMITED WARRANTY 

Manufacturer warrants this product to the original purchaser for a period of one (1) year from date of 
purchase to be free from defects in material and workmanship, but not against damages by misuse, 
negligence, accident, faulty installations and instructions.  Manufacturer will repair or replace (at 
factory’s option), free of charge, any component of the equipment thus found to be defective, on return 
of the component, “PREPAID” to the factory during the warranty period.  In no event shall any liability 
or obligation of the Manufacturer arising from this warranty exceed the purchase price of the equipment.  
This warranty is only valid if the defective product is returned as a complete assembly without physical 
damage.  The Manufacturer’s liability, as stated herein, cannot be altered or enlarged except by a written 
statement signed by an officer of the company.  In no event shall the Manufacturer be liable for 
consequential or incidental damages.  A return authorization is required from Techcon Systems prior to 
shipping a defective unit to the factory. 
 
Manufacturer reserves the right to make engineering product modifications without notice. 
 
Send warranty returns to: 
 
OK International  
Garden Grove Division 
12151 Monarch Street 
Garden Grove, Ca 92841 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
Teflon is a registered trademark of E.I. DuPont. 
 

 

 

 

 

 

 

 

 

 

 

TSI-0130-D 

Summary of Contents for TS934













Reviews: