TEC B-SP2D Series Maintenance Manual Download Page 57

Page: 57 / 77

5-2

5. TROUBLESHOOTING

EO18-33014

5. TROUBLESHOOTING

Corrective action

Re-adjust the sensors.

Re-install the sensors.

Clean the sensors.

Connect the sensors to the

CPU PC board ass'y.

Close the media cover until

both sides of the cover click

in position.

Replace the media cover

switch.

Replace the interface PC

board ass'y.

Replace the CPU PC board

ass'y.

Connect the interface PC

board ass'y with the CPU PC

board ass'y completely.

Replace the FPC cable for

the interface PC board.

Clean the print head.

Change the media to the

specified one.

Re-adjust the sensor.

Re-install the sensor.

Clean the sensor and sensor

filter.

Connect the sensor to the

CPU PC board ass'y

completely.

Replace the power switch or

the CPU PC board ass'y.

Replace the battery cover.

Replace the top cover.

Clean the print head.

Re-install the print head ass'y

correctly.

Replace the print head ass'y.

Replace the platen.

Replace the motor idler gear,

platen idler gear, idler gear,

or platen gear.

Replace the print head ass'y.

Replace the platen.

Problem

The printer does not

print labels one by one

in the strip mode or

specified number of

labels in the batch

mode.

A cover open error

occurs after closing the

media cover.

The printer does not

print by radio

communication.

Poor print quality

The print start position is

not detected.

The power switch does

not perform.

The battery cover is not

closed completely.

Print tone is uneven.

A print error occurs in

the feed direction.

Cause

1. The sensors are not adjusted properly.

2. The sensors are not installed properly.

3. The sensors are dirty.

4. The sensors are disconnected from the CPU

PC board ass'y.

1. Either side of the media cover is unlocked.

2. The media cover switch failure

1. Interface PC board ass'y failure

2. CPU PC board ass'y failure

3. Interface PC board ass'y is disconnected

from the CPU PC board ass'y.

4. The FPC cable for the interface PC board is

broken.

1. The print head is dirty.

2. Unspecified media is used.

1. The sensor is not adjusted properly.

2. The sensor is not installed properly.

3. The sensor or the sensor filter is dirty.

4. The sensor is disconnected from the CPU

PC board ass'y.

1. Power switch failure or CPU PC board ass'y

failure

1. The battery cover failure

2. The top cover failure

1. The print head is dirty.

2. The print head ass’y is not installed in

position.

3. The print head failure

4. The platen failure

1. Failure in the motor idler gear, platen idler

gear, idler gear, or platen gear

2. Print head failure

3. Platen failure

Summary of Contents for B-SP2D Series














































































Search results

Summary of Contents for B-SP2D Series

Reviews:

Related manuals for B-SP2D Series

Brands by name

Popular brands

TEC B-SP2D Series, Maintenance Manual

Search results

Summary of Contents for B-SP2D Series

Reviews:

Related manuals for B-SP2D Series

Brands by name

Popular brands