(L) Turn the FD PWR switch of the SKA off at the track 00 position and
then set it again to the PSA side. Confirm that the stop position
of the head carriage did not change at power off and on.
(m) If the value in item (j) or (L) is out of the specified range, adjust
the position of the track 00 sensor according to the Following
procedure.
i) Loosen the fixing screw of the track 00 stopper (see Fig.434) and
shift the stopper in the step-out direction (make apart from the
rear side of the head carriage),
ii) Connect the 2nd channel of the oscilloscope to TP9 or TP10
(Differentiation amp.) of the PCBA MFD control and change the
trigger to this channel.
Oscilloscope range: AC mode, 0.2V, 20msec
iii) Install an alignment disk. The track alignment should be correctly
adjusted according to item 4-4-13.
iv) Key in "CO" and confirm that the track indicator becomes '"00".
(RECALIBRATE).
v) Key in the following code and confirm that two lobe patterns as in
Fig.430 can be observed.
48tpi: C2 16
96tpi: C2 32
If normal lobe pattern cannot be observed, move the head to the
track position where the typical lobe pattern can be observed by
stepping in by key "8" or by stepping out by key ■"9".
vi) Remove the alignment disk,
vii) Key in the following code. (SET TRACK NUMBER)
48tpi:
E4 16
96tpi: E4 32
viii) Key in "C2 00"
(SEEK 00)
Don't
key in "CO" (RECALIBRATE),
ix) Change the connection of the oscilloscope as in item (b).
x) Key in "C5".
(TOO TIMING SEEK ±5)
4107
Summary of Contents for FD-55 Series
