manualshive.com logo in svg

TBK vision TBK-NVR2200 Series, User Manual, Page: 73 / 216

Share
Download
TBK vision TBK-NVR2200 Series User Manual Download Page 73

TBK-NVR2200 Network Video Recorder User Manual  

 

 

 

www.tbkvision.com

 

 

 

73

 

Chapter 5 Recording Settings  

5.1 Configuring Parameters  

Purpose:  

 

By configuring the parameters you can define the parameters which affect the image quality, such 

as the transmission stream type, the resolution and so on. 

 

Before you start:

 

 

1)

 

Make sure that the HDD has already been installed. If not, please install a HDD and 
initialize it. (Menu>HDD>General) 

 

 

 

Figure 5-1

 

HDD- General 

 

2)

 

Check the storage mode of the HDD 

 

Click 

Advanced

 to check the storage mode of the HDD.  

 

If the HDD mode is 

Quota

, please set the maximum record capacity and maximum picture 

capacity. For detailed information, see 

Chapter

 

Configuring Quota Mode.

 

 

If the HDD mode is 

Group

, you should set the HDD group. For detailed information, see 

Chapter Configuring HDD Group for Recording.

 

 

 

 

Figure 5-2

 

HDD- Advanced 

 

Step 1

 

Enter the Record settings interface to configure the recording parameters: 

 

Menu > Record > Parameters 

 

Summary of Contents for TBK-NVR2200 Series

























































































































































































































Reviews:

No comments