background image

45

Copyright Notice

Copyright © 2000 Targus Group International, Inc. All rights reserved.

Targus and the Targus logo are registered trademarks of Targus Group 
International. 

Battery Friendly is a trademark of Socket Communications, Inc. 

Windows CE and Windows Powered Pocket PC are registered 
trademarks of Microsoft Corp.

All other trademarks, registered trademarks, brand, and product names 
are the property of their respective owners.

Reproduction of the contents of this manual without the permission of 
Targus is expressly prohibited.

Regulatory Compliance

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC rules. This 
equipment is also CE EN55022 and C-TICK compliant. These limits are 
designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instruction manual, 
may cause harmful interference to radio communications. Operation of 
this equipment in a residential area is likely to cause harmful interference 
in which case the user will be required to correct the interference at his or 
her own expense.

If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, 
the user may try to correct the interference by one or more of the 
following measures:

Reorient or relocate the receiving antenna of the radio or television.

Increase the distance separating the equipment and the receiver.

Connect the equipment to an outlet on a different branch circuit than 
that of the receiver.

Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for PA610U

















































Reviews: