TallyGenicom T6200 Series Operator'S Manual Download Page 31

Page: 31 / 92

2–3

Chapter 2: Printer Control Panel

Paper Indicators

The Paper Indicators occupy position 16 of the first line of the display. Table
2-1 shows the meaning of each indicator.

Indicator

Paper Weight

Impact

(blank)

The platen is in the Light

The platen is in the Normal

Weight zone when Paper

Impact zone when Impact is

Weight is on Auto or set

on Auto or set to Normal.

to Light.

The platen is in the Medium The platen is in the Normal
Weight zone when Paper

Impact zone when Impact

Weight is on Auto or set to

is on Auto ot set to Normal.

to Medium.

Paper Weight is set to

The platen is in the Normal

Heavy.

Impact zone when Impact is
on Auto or set to Normal.

The platen is in the Medium The platen is in the High
Weight zone when Paper

Impact zone when Impact is

Weight is on Auto or set to

is on Auto ot set to High.

to Medium.

The platen is in the Heavy

The platen is in the High

Weight zone when Paper

Impact zone when Impact is

Weight is on Auto or set to

is on Auto ot set to High.

to Heavy.

The platen is in the Light

Impact is set to High.

Weight zone when Paper
Weight is on Auto or set to
to Light.

Table 2 - 1 Paper Weight Indicators

Summary of Contents for T6200 Series





























































































Search results

Summary of Contents for T6200 Series

Reviews:

Related manuals for T6200 Series

Brands by name

Popular brands

TallyGenicom T6200 Series, Operator'S Manual

Search results

Summary of Contents for T6200 Series

Reviews:

Related manuals for T6200 Series

Brands by name

Popular brands