Synthes TFN Technique Manual Download Page 23 | Manualshive

Page: 23 / 84

background image

1

Verify nail insertion depth and anteversion

Instruments

357.365 Aiming Arm for TFN, 125°

357.366 Aiming Arm for TFN, 130°

357.367 Aiming Arm for TFN, 135°

357.399 Guide Wire 3.2 mm, length 400 mm

Ensure that the nail is tightly connected to the insertion
handle.

Securely attach the appropriate aiming arm to the insertion
handle.

Nail insertion depth can be confirmed by inserting a 3.2 mm
guide wire through the aiming arm. To ensure the correct an-
teversion of the nail, an additional guide wire can be inserted
ventral to the femoral neck and into the femoral head. Take
a lateral image of the proximal femur to verify nail rotation
and ensure that the head element will be aimed toward the
center of the femoral head.

Proximal Locking

TFN – Titanium Trochanteric Fixation Nail System

Technique Guide

Synthes

21

«
...
21
22
23
24
25
...
»

Summary of Contents for TFN





















































































Reviews:

No comments

Related manuals for TFN

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: XAG Pages: 24

Brand: Malmet Pages: 14

Brand: Zempire Pages: 2

Brand: Handler Pages: 25

Brand: Wahl Pages: 47

Brand: ICELED Pages: 4

Brand: Facom Pages: 4

Brand: FaceLake Pages: 2

Brand: G-Lab Pages: 16

Brand: G&G Pages: 2

Brand: Jasco Pages: 2

Frontier FC5706

Brand: OHAUS Pages: 47

Brand: Ocutech Pages: 4

Brand: Wassermann Pages: 24

Brand: A.HABERKORN Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands