Synthes TFN Technique Manual Download Page 33 | Manualshive

Page: 33 / 84

background image

Option B
Proximal locking with screw

Instruments

357.052 Compression Nut, for No. 357.048

357.377 Connecting Screw for Helical Blade for TFN

357.428 Inserter/Extractor for TFN

Femoral Neck Screw

Thread the compression nut completely onto the screw in-
serter/extractor. Insert the helical blade connecting screw into
the screw inserter/extractor. Align the arrows on the tabs
of the inserter/extractor with the flats on the back end of the
screw. Thread the connecting screw into the screw and
finger tighten the assembly.

Pass the screw insertion assembly over the guide wire,
through the blade guide sleeve and through the nail.
Advance the screw by turning the inserter/extractor clock-
wise until the mark on the inserter meets the flange surface
of the blade guide sleeve. At this depth the screw tip will
be positioned at the tip of the guide wire.

TFN – Titanium Trochanteric Fixation Nail System

Technique Guide

Synthes

31

«
...
31
32
33
34
35
...
»

Summary of Contents for TFN





















































































Reviews:

No comments

Related manuals for TFN

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

Brand: JB-Lighting Pages: 60

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: ZIGBEE Pages: 4

Brand: CAIRE Pages: 38

Brand: Caframo Pages: 72

Brand: Danfoss Pages: 106

Brand: Eaton Pages: 16

Brand: Eaton Pages: 6

Brand: Ecco Pages: 17

Brand: H&S Pages: 42

MiniLift160 Classic

Brand: Handicare Pages: 28

Brand: Hands Free Farm Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands