Synthes TFN Technique Manual Download Page 25 | Manualshive

Page: 25 / 84

background image

Important:

The blade guide sleeve should rest on the lateral

cortex. Do not overtighten on the cortex as this may affect
the accuracy of the aiming assembly.

Turn the buttress/compression nut counterclockwise to ad-
vance the blade guide sleeve to the bone. The buttress/com-
pression nut is locked into the aiming arm, ensuring that the
blade guide sleeve will remain in position on the lateral
cortex throughout the remainder of the procedure for head
element insertion. Take an AP C-arm image to confirm that
the blade guide sleeve is on the lateral cortex.

Reconfirm fracture reduction using image intensification.

TFN – Titanium Trochanteric Fixation Nail System

Technique Guide

Synthes

23

«
...
23
24
25
26
27
...
»

Summary of Contents for TFN





















































































Reviews:

No comments

Related manuals for TFN

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Brand: B&K Pages: 5

Brand: B&K Pages: 28

Brand: Cadman Pages: 66

Brand: Jacobs Ladder Pages: 16

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: Panasonic Pages: 180

Brand: Vahle Pages: 96

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: Mackie Pages: 34

Brand: Mackworth Pages: 38

Brand: P&P Pages: 6

Brand: QRS Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands