Synthes TFN Technique Manual Download Page 31

Page: 31 / 84

Tap/ream (Optional)

Instrument

357.430 Tap/Reamer for TFN Femoral Neck Screw

Important: Only use the tap/reamer when proximal
locking is done with the TFN screw.

The tap/reamer may be used to prepare a pathway for the
TFN screw.

Important:

Only use the tap/reamer in dense bone.

Pass the tap/reamer over the guide wire, through the blade
guide sleeve and through the nail. Advance the tap/reamer
manually by turning clockwise until the tip of the tap/reamer
reaches the desired screw placement in the femoral head.

Important:

There is no stop on the tap/reamer so monitor-

ing insertion via the following methods is recommended:
– Monitor the depth under fluoroscopy.
– Monitor the respective graduations on the instrument

shaft in relation to the blade guide sleeve.

Remove the tap/reamer by turning counterclockwise.

TFN – Titanium Trochanteric Fixation Nail System

Technique Guide

Synthes

Summary of Contents for TFN





















































































Search results

Summary of Contents for TFN

Reviews:

Related manuals for TFN

Brands by name

Popular brands

Synthes TFN, Technique Manual

Search results

Summary of Contents for TFN

Reviews:

Related manuals for TFN

Brands by name

Popular brands