LAMBDA 10-3 OPERATION MANUAL – REV. 3.03 (20110829)
80
Table 8-3. PC and Lambda 10-3 parallel port pin assignments
Pin #
Pin #
Pin #
Pin # PC Parallel Port
PC Parallel Port
PC Parallel Port
PC Parallel Port
Lambda 10
Lambda 10
Lambda 10
Lambda 10----3 Controller
3 Controller
3 Controller
3 Controller
1
1
1
1
Strobe
Not Connected (NC)
2
2
2
2
Bit 0 Data
Command Byte Bit 0 (Filter Wheel Command: Position Bit 0)
3
3
3
3
Bit 1 Data
Command Byte Bit 1 (Filter Wheel Command: Position Bit 1)
4
4
4
4
Bit 2 Data
Command Byte Bit 2 (Filter Wheel Command: Position Bit 2)
5
5
5
5
Bit 3 Data
Command Byte Bit 3 (Filter Wheel Command: Position Bit 3)
6
6
6
6
Bit 4 Data
Command Byte Bit 4 (Filter Wheel Command: Speed Bit 0)
7
7
7
7
Bit 5 Data
Command Byte Bit 5 (Filter Wheel Command: Speed Bit 1)
8
8
8
8
Bit 6 Data
Command Byte Bit 6 (Filter Wheel Command: Speed Bit 2)
9
9
9
9
Bit 7 Data
Command Byte Bit 7 (Filter Wheel Command: Wheel Select Bit)
10
10
10
10
ACK
NC
11
11
11
11
Busy
Busy Line Output
12
12
12
12
PE
Error Line Output
13
13
13
13
Select
NC
14
14
14
14
Autofeed
Shutter A open/close (see Chapters 8 and 9 for more information)
15
15
15
15
Error
NC
16
16
16
16
Init
Shutter B open/close (see Chapters 8 and 9 for more information)
17
17
17
17
Select In
NC
18
18
18
18
Ground
NC
19
19
19
19
Ground
NC
20
20
20
20
Ground
NC
21
21
21
21
Ground
NC
22
22
22
22
Ground
NC
23
23
23
23
Ground
NC
24
24
24
24
Ground
Ground
25
25
25
25
Ground
Ground
8.5.2
8.5.2
8.5.2
8.5.2
Input Command Structure
Input Command Structure
Input Command Structure
Input Command Structure
Input Commands may be sent through the printer adapter using an OUT
OUT
OUT
OUT command from
basic, or an equivalent command from another language. In
Microsoft QuickBasic
the form of
the command is:
OUT
OUT
OUT
OUT port, data
Where the decimal value of port would be 956, 888, or 632 depending on your system, and
data would be a number indicating the desired speed and filter number.
The number to use for data can be generated from the desired speed and filter as follows:
data = wheel[0 for A; 128 for B] + filter po (speed * 16)
Thus, to command a move to Wheel A, Filter Position 1, at Speed 1 (0 + 1 + 16 = 17), using
a printer adapter having a base address of 888, you would use the following command:
OUT 888, 17
Summary of Contents for Lambda 10-3
