Supermicro Supero 6037R-E1R16N User Manual Download Page 73

Page: 73 / 75

B-1

Appendix B: System Specifications

Appendix B

System Specifications

Processors

Single or dual Intel® Xeon E5-2600 Series processors

Note: Please refer to our web site for a complete listing of supported processors.

Chipset

Intel C600 chipset

BIOS

32 Mb AMI® SPI Flash ROM

Memory Capacity

Twenty-four DIMM sockets supporting up to 1.5 TB of LRDIMMs (Load
Reduced DIMMs), 768 Gb of RDIMM (Registered DIMMs) or 128 GB of UDIMM
(Unbuffered UDIMMs) ECC/Non-ECC DDR3-1866/1600/1333/1066/800 memory

Note: see Section 5-5 for details.

Drive Bays

Sixteen hot-swap drive bays to house SATA drives

Peripheral Drive Bays

One slim DVD-ROM drive

Expansion Slots

Four PCI-E 3.0 x16 slots, one PCI-E 3.0 x8 slot and one PCI-E 3.0 x4 (in a x8)
slot

Serverboard

X9DRi-LN4F+ (Extended ATX form factor)
Dimensions: 13.68 x 13 in (347 x 330 mm)

Summary of Contents for Supero 6037R-E1R16N












































































Search results

Summary of Contents for Supero 6037R-E1R16N

Reviews:

Related manuals for Supero 6037R-E1R16N

Brands by name

Popular brands

Supermicro Supero 6037R-E1R16N, User Manual

Search results

Summary of Contents for Supero 6037R-E1R16N

Reviews:

Related manuals for Supero 6037R-E1R16N

Brands by name

Popular brands