Supermicro Supero 6037R-E1R16N, User Manual

Page: 63 / 75

Chapter 7: BIOS
7-19 7-18
S
UPER
S
TORAGE
S
YSTEM 6037R-E1R16N User's Manual
PERR# Generation
Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus
Signal Error Event. The options are Enabled and
Disabled .
SERR# Generation
Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus
Signal Error Event. The options are
Enabled and Disabled.
Maximum Payload
Select Auto to allow the system BIOS to automatically set the maximum payload
value for a PCI-E device to enhance system performance. The options are
Auto
,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
Maximum Read Request
Select Auto to allow the system BIOS to automatically set the maximum Read
Request size for a PCI-E device to enhance system performance. The options are
Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
ASPM Support
This feature allows the user to set the Active State Power Management (ASPM)
level for a PCI-E device. Select Force L0 to force all PCI-E links to operate at L0
state. Select Auto to allow the system BIOS to automatically set the ASPM level for
the system. Select Disabled to disable ASPM support. The options are
Disabled
,
Force L0, and Auto.
Warning : Enabling ASPM support may cause some PCI-E devices to fail!
CPU1 Slot 1 PCI-E 3.0 x16 OPROM/CPU1 Slot 2 PCI-E 3.0 x4 OPROM/CPU1
Slot 3 PCI-E 3.0 x16 OPROM/CPU2 Slot 1 PCI-E 3.0 x16 OPROM/CPU2 Slot
2 PCI-E 3.0 x16 OPROM/CPU1 Slot 1 PCI-E 3.0 x8 OPROM
Select Enabled to enable Option ROM support to boot the computer using a
network interface from the slots specified above. The options are Enabled and
Disabled.
Onboard LAN Option ROM Select
Select iSCSI to use the iSCSI Option ROM to boot the computer using a network
device. Select PXE (Preboot Execution Environment) to use an PXE Option ROM
to boot the computer using a network device. The options are iSCSI and
PXE .
Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM/ Load
Onboard LAN3 Option ROM/Load Onboard LAN4 Option ROM
Select Enabled to enable the onboard LAN1 Option ROM~LAN4 Option ROM.
This is to boot the computer using a network device. The default setting for LAN1
Option ROM is Enabled , and the default settings for LAN2 Option ROM~LAN4
Option ROM are Disabled .
VGA Priority
This feature allows the user to select the graphics adapter to be used as the primary
boot device. The options are
Onboard VGA
, and Add-on VGA.
Network Stack
Select Enabled enable PXE (Preboot Execution Environment) or UEFI (Unified
Extensible Firmware Interface) for network stack support. The options are Enabled
and
Disabled .

Serial Port 1 Configuration/Serial Port 2 Configuration
Serial Port
Select Enabled to enable a serial port specified by the user. The options are En-
abled and Disabled.
Device Settings
This feature indicated if reset is required or not for a serial port specified.
Change Settings
Use this feature to set the optimal Environment_Control_Interface (PECI) setting for
a serial port specified. The default setting is
Auto
, which will allow the AMI BIOS
to automatically select the best setting for the PECI platform.
Device Mode
Use this feature to select the desired mode for a serial port specified. The options
are Normal and High Speed.

Serial Port Console Redirection
•
COM 0/COM1
These two submenus allow the user to configure the following Console Redirection
settings for a COM Port specified by the user.
Console Redirection
Select Enabled to use a COM Port selected by the user for Console Redirection.
The options are
Enabled and Disabled.