manualshive.com logo in svg

Supermicro SSE-F3548S, User Manual

The Supermicro SSE-F3548S is a high-performance network switch designed for efficient data management. Enhance your network with ease using this versatile device. Explore its full potential by accessing the comprehensive User Manual, available for free download from our website, offering valuable guidance on installation, customization, and troubleshooting.

Share
Download
background image

 

 

Supermicro SSE-F3548S/SSE-F3548SR Configuration User’s Guide 

219 

 

8.1.1

 

MAC Extended ACL 

A MAC Extended ACL allows users to control the traffic based on the fields in Ethernet MAC and VLAN 

headers.  

Users can configure the traffic flow based on the source MAC address, destination MAC address or 

Ethernet type field value. Users can also use VLAN identifiers to configure the traffic flow.  

Users can choose to deny, redirect or permit the configured traffic flow using a MAC Extended ACL. 

8.1.2

 

IP Standard ACL 

An IP Standard ACL allows users to control the traffic based on the fields in an IP header.  

Users can configure the traffic flow based on the source IP address and destination IP address.  

Users can choose to deny, redirect or permit the configured traffic flow using an IP Standard ACL. 

8.1.3

 

IP Extended ACL 

An IP Extended ACL allows users to control traffic based on fields in an IP header, ICMP header, TCP 

header and UDP header.  

Users can configure the traffic flow based on source IP address, destination IP address,protocol field in IP 

header, TOS field in IP header or by using a DSCP priority in an IP header. 

Users can also configure the traffic flow based on ICMP message type, ICMP message code, TCP port 

number or UDP port number. 

Users can choose to deny, redirect or permit the configured traffic flow using an IP Extended ACL. 

8.2

 

 MAC Extended ACL 

Supermicro switches support up to 128 MAC Extended ACLs.  

Users can define a MAC Extended ACL with a deny, permit or redirect action rule. A MAC Extended ACL 

can be defined only with one rule. To implement multiple rule ACLs, configure multiple MAC Extended 

ACLs. 

 

 

There is no implied deny all rule in Supermicro switch ACLs. By default, all packets not 

matching a configured ACL rule will be forwarded automatically. For any traffic to be denied, 

it has to be configured with an explicit deny rule. 

 

Three  
types  
of ACL 

MAC Extended ACL  
IP Standard ACL 
IP Extended ACL 

Summary of Contents for SSE-F3548S















































































































































































































































































































































































Reviews:

No comments

Related manuals for SSE-F3548S

United Electric Controls 54 Series Assembly, Installation And Operation Instructions preview
54 Series
Brand: United Electric Controls Pages: 6
rako WCM-D Instruction Manual preview
WCM-D
Brand: rako Pages: 4
DAITEM SA706AX Installation Manual preview
SA706AX
Brand: DAITEM Pages: 37
GHIELMETTI 674.115.420.30 Operation Manual preview
674.115.420.30
Brand: GHIELMETTI Pages: 12
Mellanox Technologies MIS5023 Dismantling Manual preview
MIS5023
Brand: Mellanox Technologies Pages: 12
Cabletron Systems FlowPoint 2100 12 User Manual preview
FlowPoint 2100 12
Brand: Cabletron Systems Pages: 36
Hawking PN824ES Specifications preview
PN824ES
Brand: Hawking Pages: 2
Xunison Hub D60 5G Quick Start Manual preview
Hub D60 5G
Brand: Xunison Pages: 14
Lantech IPES-2208CA User Manual preview
IPES-2208CA
Brand: Lantech Pages: 146
Versa Technology VX-IGP-1204F User Manual preview
VX-IGP-1204F
Brand: Versa Technology Pages: 96
Whelen Engineering Company PCCS9LW Installation Manual preview
PCCS9LW
Brand: Whelen Engineering Company Pages: 5
InvoTek BlueHub User Manual preview
BlueHub
Brand: InvoTek Pages: 4
Kramer VP-440X User Manual preview
VP-440X
Brand: Kramer Pages: 71
Cabletron Systems GIGAswitch GSR-16 User'S Reference Manual preview
GIGAswitch GSR-16
Brand: Cabletron Systems Pages: 346
Belkin P73957EH Quick Setup Manual preview
P73957EH
Brand: Belkin Pages: 2
Gefen EXT-HDMI-441 User Manual preview
EXT-HDMI-441
Brand: Gefen Pages: 12
NTI SM-4X4-4K18GBA-LC Operating Instruction preview
SM-4X4-4K18GBA-LC
Brand: NTI Pages: 18
IMC Networks PoE Giga-MiniMc Operation Manual preview
PoE Giga-MiniMc
Brand: IMC Networks Pages: 28

Brands by name

Popular brands

Load more brands