manualshive.com logo in svg

Supermicro SSE-F3548S, User Manual

The Supermicro SSE-F3548S is a high-performance network switch designed for efficient data management. Enhance your network with ease using this versatile device. Explore its full potential by accessing the comprehensive User Manual, available for free download from our website, offering valuable guidance on installation, customization, and troubleshooting.

Share
Download
background image

 

 

Supermicro SSE-F3548S/SSE-F3548SR Configuration User’s Guide 

237 

SMIS(config-std-nacl)# permit host 172.20.20.1 host 172.100.0.1 

Then create the deny rule for the subnet 172.20.0.0. 

SMIS# configure terminal 

SMIS(config)# ip access-list standard acl_1b 

SMIS(config-std-nacl)# deny 172.20.0.0 255.255.0.0 172.100.0.0 255.255.0.0 

ACL 2 Configuration 

SMIS# configure terminal 

SMIS(config)# ip access-list standard 2 

SMIS(config-std-nacl)# redirect fx 0/1 any 172.10.0.0 255.255.0.0 

8.3.9

 

IP Extended ACLs 

Supermicro switches support 128 IP ACLs, which includes both IP Standard and IP Extended ACLs. 

Users can define IP Extended ACLs with deny, permit or redirect action rules. An IP Extended ACL can be 

defined only with one rule.  

 

There is no implied deny all rule in Supermicro switch ACLs. By default, all packets not 

matching a configured ACL rule will be forwarded automatically. For any traffic to be denied, 

it has to be configured with an explicit deny rule. 

 

The permit rule is widely used for QoS applications. In some cases permit rules are useful when all traffic 

is denied by a rule and a few specific hosts are to be permitted. IP Extended ACLs allow users to configure 

traffic flow with the following fields. 

 

IP -  Protocol, Source IP Address, Destination IP Address, Type Of Service (TOS), DSCP 

 

TCP – Source Port, Destination Port, TCP message type – acknowledgement / reset 

 

UDP – Source Port, Destination Port 

 

ICMP – Message Type, Message Code 

IP Extended ACL rules can be created and identified either a with an ACL number such as 1,2 or 3 or with a 

name string. ACL identifier numberscan be any number from 1 to 65535. ACL identifier namescan be any 

string length not exceeding 32 characters. 

 

IP Standard ACLs and IP Extended ACLs share the ACL numbers and names. Hence ACL 

numbers and names across all IP Standard and IP Extended ACLs have to be unique. In other 

words, the same ACL number or name cannot be used for both IP Standard ACLs and IP 

Extended ACLs. 

 

User can associatepriority values to IP Extended ACL rules. Based on the configured priority, the rules will 

be orderly arranged on the hardware ACL table. The ACL rules are checked on the incoming packets based 

on the order of priority. The higher priority ACL rules takes precedence over the lower priority rules. In 

Summary of Contents for SSE-F3548S















































































































































































































































































































































































Reviews:

No comments

Related manuals for SSE-F3548S

Campbell SDS-122 Instruction Manual preview
SDS-122
Brand: Campbell Pages: 14
H3C S9500E Series Connecting Manual preview
S9500E Series
Brand: H3C Pages: 13
H3C S9500E Series Security Configuration Manual preview
S9500E Series
Brand: H3C Pages: 207
H3C S3100-52P Operation Manual preview
S3100-52P
Brand: H3C Pages: 62
Pathway connectivity solutions 1016 Manual preview
1016
Brand: Pathway connectivity solutions Pages: 2
Cablematic HUB-1230i User Manual preview
HUB-1230i
Brand: Cablematic Pages: 8
Erbe 20186-007 Manual preview
20186-007
Brand: Erbe Pages: 118
N-Tron 100-POE4-MDR User Manual & Installation Manual preview
100-POE4-MDR
Brand: N-Tron Pages: 17
Key Digital KD-MS4x4G-2 Manual preview
KD-MS4x4G-2
Brand: Key Digital Pages: 20
Campbell Hausfeld CW301300AJ Additional Operating Instructions preview
CW301300AJ
Brand: Campbell Hausfeld Pages: 4
Linkskey LKU -UA02 Quick Installation Manual preview
LKU -UA02
Brand: Linkskey Pages: 2
Lantech IPES-2208CA User Manual preview
IPES-2208CA
Brand: Lantech Pages: 146
Advantech EKI-2525P User Manual preview
EKI-2525P
Brand: Advantech Pages: 28
IPGARD SDPN-2D Manual preview
SDPN-2D
Brand: IPGARD Pages: 15
Stahl 8070/2 Series Manual preview
8070/2 Series
Brand: Stahl Pages: 58
MicroNet SP684C User Manual preview
SP684C
Brand: MicroNet Pages: 74
W&T IP-Watcher 2x2 Digital PoE Manual preview
IP-Watcher 2x2 Digital PoE
Brand: W&T Pages: 79
Ascent Communication Technology ACT AS2308S Quick Reference Manual preview
ACT AS2308S
Brand: Ascent Communication Technology Pages: 8

Brands by name

Popular brands

Load more brands