background image

SuperiorFireplaces.us.com

126871-01B

18

INSTALLATION

Continued

 CAUTION: Never connect pro-

pane/LP fi replace directly to the 
propane/LP supply. This fi replace 
requires  an  external  regulator 
(not supplied). Install the external 
regulator  between  the  fi replace 
and propane/LP supply.

  WARNING:  Never  connect 

natural gas fi replace to private 
(non-utility)  gas  wells.  This 
gas  is  commonly  known  as 
wellhead gas.

For  propane/LP  units,  installer  must  supply 
an external regulator. The external regulator 
will reduce incoming gas pressure. You must 
reduce  incoming  gas  pressure  to  between 
11"  and  14"  of  water.  If  you  do  not  reduce 
incoming  gas  pressure,  fi replace  regulator 
damage could occur. Install external regula-
tor with the vent pointing down as shown in 

Figure 21

. Pointing the vent down protects it 

from freezing rain or sleet.

  CAUTION:  Use  only  new, 

black  iron  or  steel  pipe.  In-
ternally-tinned copper tubing 
may be used in certain areas. 
Check  your  local  codes.  Use 

pipe of 1/2" or greater diameter 
to  allow  proper  gas  volume  to 
fi replace.  If  pipe  is  too  small, 
undue loss of volume will occur.

Propane/LP 
Supply Tank

External 
Regulator

Figure 21- External Regulator with Vent 

Pointing Down

Vent 
Pointing 
Down

Extension Cord

Use extension cord if needed. The cord must 
have  a  three-prong,  grounding  plug  and  a 
three-hole receptacle. Make sure cord is in good 
shape. It must be heavy enough to carry the 
current needed. An undersized cord will cause 
a drop in line voltage. This will result in loss of 
power and overheating. Use a No. 16 AWG cord 
for lengths less than 50 feet.

CONNECTING TO GAS SUPPLY

  WARNING:  This  appliance 

requires  a  45°  male  fl are  fi tting 
5/8"-18 UNF (Unifi ed National Fine 
Thread) inlet connection and the 
fl exible gas line provided.

  WARNING:  A  qualified 

service  person  must  connect 
fi replace to gas supply. Follow 
all local codes.

Figure 20 - Installing Blower Bracket 

Assembly 

3
2
1

Blower Bracket 
Assembly 

Screw 

Wire Harness

Power 
Cord 

Valve 
Cover 
Shield 

Box Cover 

Wire 
Harness

Switch Plate 

Switch

Clamp Connector 
(not included) 

Outlet 
Receptacle 

Blue

Red

Plastic 
Wire Strap

All manuals and user guides at all-guides.com

Summary of Contents for VCM3026ZTN





































Reviews: