background image

SuperiorFireplaces.us.com

126871-01B

16

3
2
1

INSTALLATION

Continued

Figure 16 - Removing Valve Cover Shield 

1

2

Remove
Screw

Valve 
Cover 
Shield 

Shoulder 
Screw 

Branch Support

Snap Bushings

Bottom Louver 
Assembly 

4.  Carefully  disconnect  green  and  white 

wires at their insulated connectors.

5.  In top of heater cabinet, locate 4 mounting 

holes on outer casing. Align these 4 holes 
with  those  on  blower  bracket  assembly. 
Attach blower bracket assembly to outer 
casing with 

4 #10 screws provided 

(see

 

Figure 17

)

.

6.  Route  wire  harness  through  hole  in  left 

side of baffl e. Pull wire harness through 
lower opening above where valve shield 
was removed 

(see

 Figure 17

)

7.  Insert  4  wire  harnesses  into  one  of  the 

round holes in rear of valve cover shield 
and  through  rectangular  hole  in  front  of 
shield

 (see

 Figure 17

).

8.  Reconnect red wire to switch position 3. 

Reconnect blue wire to switch position 1. 
Reconnect green and white wires.

9.  Install switch plate on valve cover shield 

with 2 #10 screws provided 

(see 

Figure 

18,  Page  17

)

.  Reinstall  valve  cover 

shield. Route power cord out of cabinet 
by inserting it through bushing on outer 
casing 

(see

 Figure 17

)

. Plug fan kit into 

120-Volt grounded power supply and test 
operation.

Installing Blower Assembly

  CAUTION:  Label  all  wires 

prior  to  disconnection  when 
servicing controls. Wiring errors 
can cause improper and danger-
ous operation.

 CAUTION: Verify proper op-

eration after servicing.

NOTE

:  If  you  are  using  a  mantel  with  your 

heater, use the following instructions. If your 
heater is built-in, see For Built-In Installation 
on 

Page 17

1.  Install snap bushings found in hardware kit 

into both holes in rear of valve cover shield.

2.  Make  sure  the  wire  harness  is  firmly 

connected to the terminals on the blower 
bracket assembly. 

3.  Note wire locations on back of AUTO/OFF/

ON switch. Terminals on back of switch are 
numbered  1,  2,  and  3.  Carefully  remove 
red  wire  from  terminal  1  and  blue  wire 
from terminal 3. Black wire can remain on 
middle terminal 2

 (see 

Figure 17

).

Figure 17 - Installing Blower Bracket 

Assembly 

Wire 
Harness

Blower Bracket 
Assembly 

Screw 

Valve Cover 
Shield 

Box Cover  Wire 

Harness

Switch 
Plate 

Switch

Baffl e 

Wiring Routing 
Hole in Baffl e 

Blue

Red

Power 
Cord 

 

NOTE

:  If  you  do  not  have  a  short  Phil-

lips screwdriver, the screen, log set, and 
branch  support  must  be  removed  so  a 
longer  screwdriver  may  be  used.  See 
Connecting  Equipment  Shutoff  Valve  to 
Heater Control,

 Page 19

, steps 1 and 2.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for VCM3026ZTN





































Reviews: