26
APPENDIX D
Resetting Remote Communication and Reprogramming the Motor
This procedure will completely reset the communication between the Remote Transmitter and Motor, as well
as erase and reprogram the
Open
and
Closed
stop position settings of the Motor.
This procedure programs the Awning Motor to accept commands from one primary Remote Transmitter.
This procedure overwrites the factory set
Open
and
Closed
positions with new
Open
and
Closed
positions.
Note: To ONLY change the Open and Close preset positions, follow the procedure in Appendix A on Page 22.
Tools needed: A pen or similar pointing device is needed to press and hold the Programming Button.
To
ADD
an
additional Control Device (such as another Remote or Channel, or a Wirless Wall Switch);
•
Press the Programming button on the back of the Transmitter that was supplied with the Awning until
the motor “jogs.”
• On the
additional Control Device, press the Programming button until the motor “jogs,” then release.
To
DELETE
a Control Device, repeat the two steps listed above and the additional Control Device is removed.
To Add or Delete a Control Device (Transmitter)
WARNING: ALL STEPS MUST BE FOLLOWED EXACTLY AND COMPLETELY.
1.
Set the Remote Transmitter to Channel 1 (for single channel Remote, skip this step).
2.
Press and Hold the
my
button; the red LED light should blink for at least 5 seconds.
3.
Disconnect Power for two (2) full seconds.
4.
Connect Power for ten (10) full seconds.
5.
Disconnect Power for two (2) full seconds.
6.
Connect Power. The Awning should move, then stop on its own.
7. Press and hold the
Programming
button for ten (10) seconds, watching for two (2)
separate jogs back and forth, several seconds apart.
Note: A single jog is defined as a quick two-direction movement of the motor.
8.
Press and Hold the
CLOSE
and
OPEN
buttons together, release when the Awning jogs.
Note
:
The Awning now moves ONLY while holding down the CLOSE or OPEN button.
9. Press the
OPEN
button to check the direction of the motor.
Note: The fabric must roll from the top of the Roller Bar, when opening the Awning.
10.
If the direction is incorrect, change direction by holding the
my
button until the motor jogs.
Press the
OPEN
button again to check for the correct direction of the motor rotation.
11.
Move the Awning to the desired
Closed
position.
Note: Fabric must roll over top of Roller Bar.
12.
Press and Hold the
my
and
OPEN
buttons together; release when the Awning begins to
Open
.
13.
Press the
my
button to
Stop
the Awning at the desired
Open
setting.
14.
Make desired adjustments to the
Open
position.
15.
Press and Hold the
my
and
CLOSE
buttons simultaneously; release them when the Awning
begins to
Close
.
Let the Awning stop on its own
at the
Closed
position set in step 11.
16.
Press and Hold the
my
button; release when the Awning jogs. This step stores the new
Open
and
Close
positions.
SET PROPER DIRECTION OF MOTOR ROTATION
SET THE CLOSED AND OPEN POSITIONS
PREPARE MOTOR - Read these instructions FIRST, completely and thoroughly
17. Press and Hold the
Programming
button; wait for a jog. This completes the procedure.
Note
: The Awning now operates with a touch and release of the
OPEN
or
CLOSE
button.
18.
Test the Awning for correct one-touch operation, using the
OPEN
and
CLOSE
buttons.
FINALIZE PROGRAMMING OF MOTOR
Note: If steps 8 - 15 fail, unplug the Awning, plug it back in, then begin again from step 8.
OPEN
Front View
my
CLOSE
Indicator Lights
Rear View
Programming
Button is
located
inside
this small
opening
Channel
Selector
Button.
