Sunlight Lion ESS 48V/100 Installation Manual Download Page 27 | Manualshive

Page: 27 / 36

background image

Operation, Safety and Installation Manual |

Li.ONESS Batteries

27

EN

7.5 Discharge Mode of Li.ONESS battery

If the battery is switched off the steps below must
be followed:

• Switch on the battery by pressing the On/Off

button of the control panel or the On/Off button
of the Compact Display Telecommunication Box.
Wait for the initialization of the BMS. The duration
of the initialization can be up to 1 minute and it is
depending on the storage period of the battery
(sleep mode).

• Battery is ready for use.

NOTE: If the battery is not used, the battery will
shut down automatically in approximately 4 hours.

Picture 47

«
...
25
26
27
28
29
...
»

Summary of Contents for Lion ESS 48V/100





































Reviews:

No comments

Related manuals for Lion ESS 48V/100

Bicycle Accessories

Brand: Baby Jogger Pages: 20

Brand: FEIYUTECH Pages: 8

Brand: FeiYu Tech Pages: 2

Brand: FeiYu Tech Pages: 2

Brand: FEIYUTECH Pages: 26

Brand: LAS Pages: 44

Brand: LAS Pages: 24

Brand: National Cycle Pages: 3

Brand: Barker Pages: 2

Brand: Z-Wave Pages: 10

Brand: UniFi Pages: 15

Brand: CYBEX Pages: 24

Brand: FAAM Pages: 19

Brand: Grixx Pages: 10

DSE-LFP51.2V50A-16sLFP36115185-50A-PB50-MC-CO07-M21A

Brand: MOTOMA Pages: 27

Brand: Datalogic Pages: 17

NG-IPCAMEV8180A

Brand: Net Generation Pages: 33

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands