manualshive.com logo in svg

Sunlight Lion ESS 48V/100, Installation Manual

Share
Download
Sunlight Lion ESS 48V/100 Installation Manual Download Page 13

Operation, Safety and Installation Manual | 

Li.ONESS Batteries

13

6. Installation Procedure

6.1 Battery Cabinet

Battery cabinet installation manual can be found 
inside the carton box.

6.1.1 Battery Cabinet assembly

•

  The manufacturer’s installation manual included 

will provide all necessary information for the 
proper cabinet assembly.

•

  

When the assembly is complete, you will find 
below the relative distance of the vertical U-Rails 
inside cabinet.

6.1.2  Battery Cabinet Sliding rails 

assembly

•

  Place the battery cabinet at the final installation 

position

•

  

Set all four (4) standing cluster set points to 
balance the battery cabinet with the floor

•

  

Open battery cabinet door using the key provided. 
It is attached at the front door panel.

•

  

Remove the perforated door as shown in the 
following picture

•

  

Connect the earth cable at one of the earthing 
bolts provided

Picture 9

:  ESS cabinet consists of two carton 

boxes

Picture 11

:  Hinge for removing door

Picture 12

:  Cabinet ground connection point

Picture 10

:  Vertical U-Rail assembly distance

EN

Summary of Contents for Lion ESS 48V/100





































Reviews:

No comments

Brands by name

Popular brands

Load more brands