©2017 Extractor Corporation
115-V 20-Amp 60-Hz SUITMATE
®
Unit
27
REMOVE AND REPLACE BRAKE RODS, BASKET, HUB, AND BRAKE DISC ASSEMBLY
'
o t
K
i
V
),567
Make certain you have all the correct parts and fasteners necessary for correct installation. Re-use any
components that are not damaged, otherwise replace them. Parts used in this process: (1) EC22 Basket and
Brake Disc Assembly, (1) AEC1506 Hub Roll Pin, (2) AEC1620 S.S. Threaded Brake Rods, (2) AEC1622 Short
Compression Springs, (2) AEC1624 S.S. Locknuts, and (1) BEC1502 Motor, 115 V 60 Hz. Plus any
components required to properly reinstall the Drive Unit Assembly (Page 23) and the Sub-Top and Top
Assemblies (Page 17).
REMOVE BRAKE RODS, BASKET, HUB, AND BRAKE DISC ASSEMBLY
1) Remove SUITMATE
®
unit from the Wall Mount Bracket. See instructions beginning on Page 14.
2) Remove Top and Sub-Top Assemblies. See instructions beginning on Page 15.
3) Remove Drive Unit Assembly. See instructions beginning on Page 23.
Note:
If
%
asket itself is damaged it must be replaced, please contact Extractor Corporation at:
(Telephone) 800-553-3353, (Fax) 847-742-3552, or (E-
0
ail) [email protected].
4) Remove the Brake Rods from the Drive Unit Assembly by removing the Locknut and Short Compression
Spring on each Brake Rod. Set the Brake Rods, springs, and locknuts aside for reassembly. Inspect and
replace the Short Compression Springs if any wear or deformation is observed.
5) Place a C-clamp over each Brake Lever Arm and under the Motor Mounting Plate. Tighten the C-clamps to
allow free rotation of the Basket and Motor shaft.
Note:
Do not remove C-clamps!
6) Rotate the Hub so that the hole for the Hub Roll Pin that holds the Basket, Hub, and Brake Disc Assembly to
the Motor shaft can be clearly seen.
7) Use a hammer and a 3/16” drift punch to remove the Hub Roll Pin that holds the Basket, Hub, and Brake
Disc Assembly to the Motor shaft. A new Hub Roll Pin is required for reassembly (Part Number AEC1506).
8) Using a small pry bar or large screwdriver, pry up on the Hub to free it from the Motor shaft. Rotate the
Basket, Hub, and Brake Disc Assembly so that even pressure is exerted evenly around the Hub and Motor
shaft. Repeat until you can manually remove the Basket and Brake Disc Assembly from the Motor shaft.
Be careful not to damage the Hub or the Motor Mounting Plate. If the Hub is
³
frozen” to the Motor shaft,
please contact Extractor Corporation at: (Telephone) 800-553-3353, (Fax) 847-742-3552,
or (E-Mail) [email protected] and explain your problem.
REPLACE BRAKE RODS, BASKET, HUB, AND BRAKE DISC ASSEMBLY
1) Push the Basket, Hub, and Brake Disc Assembly onto the Motor Shaft so that the hole in the Hub lines up
with the hole in the Motor Shaft.
Note:
Apply a light coat of grease to the
0
otor shaft to facilitate assembly.
Note:
It may be necessary to gently tap the
+
ub down onto the
0
otor shaft. Do not tap or pound directly on
the basket.
2) Use a 3/16” drive pin punch to test for the proper hole alignment of the Hub and the Motor Shaft.
3) Drive a NEW Hub Roll Pin (Part Number AEC1506) into the Hub and through the Motor Shaft so that the pin
is
À
ush with the Hub.
4) Remove the C-clamps.
5) Reinstall the Brake Rods onto the Drive Unit Assembly by installing the Locknut and Short Compression
Spring on each Brake Rod removed in step 4 above.
6) Reinstall Drive Unit Assembly. See instructions beginning on Page 23.
7) Reinstall Sub-Top and Top Assemblies. See instructions beginning on Page 17.
8) Reinstall SUITMATE
®
unit to the Wall Mount Bracket. See instructions beginning on Page 14.
9) Retest the SUITMATE
®
unit for proper operation, refer to TESTING AND OPERATION on Page 7.
Summary of Contents for Swimsuit Water Extractor 115V
Page 1: ...115V 60Hz Manual Installation Maintenance...
Page 2: ......
Page 57: ......
Page 58: ...v052017...
