Stulz ENS 14 A Technical Manual Download Page 66

Page: 66 / 110

DE / 06-2016 / 1000687

Operation

STULZ UltraSonic -System for duct humidification ENS 14 A - 18 A-

Proceed as follows to set the

operating mode

The start-up menu is displayed.

Press and hold the "Esc" button until the

cursor is under the "m".

Press and hold the "Esc" button. Immedi

ately afterwards, press and hold the "►"

button.

Main menu (factory setting) is selected.

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

►

Humidifier

Ext. request

reque

outpt: 0

Humidifier

Ext. request

reque

outpt: 0

mode

capacit 1.00

supp

15.00

room

20.00

mode

capacit 1.00

supp

15.00

room

20.00

Press and hold the "OK" button until

"±00001" appears on the mode line.

Press "OK" to save the operating mode.

Using the "►" button move the cursor to

"±00001".

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

mode

±00001

capacit 1.00

supp

15.00

room

20.00

mode

capacit 1.00

supp

15.00

room

20.00

mode

±00001

capacit 1.00

supp

15.00

room

20.00

mode

±00004

capacit 1.00

supp

15.00

room

20.00

►

▲
▼

Change the mode to the required value

using the "▲" or "▼" buttons
(e.g. change from operating mode "1" to

"4").

Press "Esc" (cursor disappears,

otherwise it does this automatically after

20 sec).

Stulz Ultrasonic Master/Slave Steuergeräte (USM/USS)

Menüaufbau Anwendungsfall 1

Befeuchtungssteuerung über externes Signal

Cursor

ESC

Cursor

Weitere Diagnosemenüs mit Cursor

und

aufrufbar.

>Stop

Set Param

Set.

Prg Name

Eine ausführliche Beschreibung

der

Diagnose-Menüebene ist

in den

allgemeinen LOGO!-Unterlagen

enthalten.

0. 123456789

1. 0123456789

2. 01234

Diagnose digit. Eingänge

Befeuchter

Ext. Anford.

Anfrd 0

Ausg: 0

B-ART

LstgFkt 1.00

ZulftKC 15.00

Raum-KC 20.00

drücken

und zusätzlich

ca. 5 s Cursor

betätigen.

Grundmenü

drücken

Inbetriebnahme

Befeuchter-Menüebene

Diagnose-Menüebene

Cursor

ESC

0. 123456789

1. 0123456

drücken

ESC OK

Programmiermenü

mode

capacit 1.00

supp

15.00

room

20.00

Summary of Contents for ENS 14 A















































































































Search results

Summary of Contents for ENS 14 A

Reviews:

Related manuals for ENS 14 A

Brands by name

Popular brands

Stulz ENS 14 A, Technical Manual

Search results

Summary of Contents for ENS 14 A

Reviews:

Related manuals for ENS 14 A

Brands by name

Popular brands