manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 8 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 8

Introduction

7

BED SYMBOLS

Warning, Refer to Service/Maintenance Manual

Alternating Current

Type B Equipment: equipment providing a particular degree of protection against

electric shock, particularly regarding allowable leakage current and reliability of the

protective earth connection.

Class 1 Equipment: equipment in which protection against electric shock does not

rely on BASIC INSULATION only, but which includes an additional safety precau-

tion in that means are provided for the connection of the EQUIPMENT to the protec-

tive earth conductor in the fixed wiring of the installation in such a way that AC-

CESSIBLE METAL PARTS cannot become live in the event of a failure of the

BASIC INSULATION.

Mode of Operation: Continuous

IPX4: Protection from liquid splash

Dangerous Voltage Symbol

Protective Earth Terminal

Potential Equalization Symbol

Component For Use in Medical Equipment Recognized by Underwriters Laborato-

ries Inc., with Respect to Electrical Shock, Fire, Mechanical and Other Specified

Hazards Only in Accordance with UL 2601

−

1 and CAN/CSA C22.2 No. 601.1

Safe Working Load Symbol

~

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments