manualshive.com logo in svg

Stryker TriaDyne III Proventa 2030, Maintenance Manual, Page: 23 / 113

Share
Download
Stryker TriaDyne III Proventa 2030 Maintenance Manual Download Page 23

Service Information

22

STATIC DISCHARGE PRECAUTIONS

The electronic circuits in the 2030 are completely protected from static electricity damage only while the bed

is assembled.  It is extremely important that all service personnel always use adequate static protection when

servicing the electronic systems of the 2030.  

Whenever you are touching wires, you should be using static

protection.

Static Protection Equipment

The necessary equipment for proper static protection is:

1 static wrist strap; 3M part number 2214 or equivalent,

1 grounding plug; 3M part number 61038 or equivalent,

1 test lead with a banana plug on one end and an alligator clip on the other; Smith part number

      N132B699 or equivalent.

  

CAUTION

All electronic service parts will be shipped in static shielding bags.  Do not open the bags until you have com-

pleted steps 2 and 3 of the following procedure.  Do not place unprotected circuit boards on the floor.  All circuit

boards to be returned to Stryker Medical should be shipped in the static shielding bags the new boards were

shipped in.

Static Protection Procedure

1. Unplug the power cord from the wall receptacle.

2. Insert the grounding plug into a properly grounded hospital grade wall receptacle. Plug the banana plug

of the test lead into the receptacle on the grounding plug.  Connect the alligator clip on the other end of

the test lead to a ground point on the bed.

3. Place the static control wrist strap on your wrist.  Connect the alligator clip at the other end of the wrist strap

cord to a ground point on the bed.

BED

GROUNDING DIAGRAM

Summary of Contents for TriaDyne III Proventa 2030


















































































































Reviews:

No comments